RoofCalc.

Measure the roof, then order the material

Eight calculators that take the numbers you can measure from the ground — footprint, pitch, ridge length — and turn them into squares, bundles, rolls, panels and vents. Each one shows the formula, the source and the point where it stops being reliable.

Start with the roof area Or follow the worked example

Calculators

Roof pitch

Rise per 12 to degrees, slope percentage and the multiplier, with the code limit for shingles.

Roof squares

Footprint, eaves and pitch to square feet and roofing squares, waste kept separate.

Shingles

Bundles of field shingles, ridge cap and starter strip, counted as three separate products.

Underlayment

Rolls of synthetic membrane or #15 and #30 felt, with the double-layer rule for low slopes.

Attic ventilation

Net free area at 1/150, split into intake and exhaust, then ridge feet and vent counts.

Gutters

Whether a 5 or 6 inch gutter handles the roof, and how many downspouts the run needs.

Sheathing

4 × 8 and 4 × 10 panel counts, plus the span rating that matches your rafter spacing.

Rafter length

Common rafter length, ridge height and cut angles from span, pitch and overhang.

Guides

Roof pitch chart

Every pitch from 1:12 to 12:12 with angle, slope and multiplier, and the derivation of each.

Shingles per square

Coverage per bundle, the real cost of waste, and why ridge cap is its own line item.

Featured scenario

Re-roofing a 1,500 sq ft ranch

A single-story 40 × 30 ft house, 6:12 pitch, 1 ft eaves, 40 ft of ridge and a 140 ft perimeter. Every number below comes from a calculator on this page and carries through to the next one.

StepResultCalculator
Roof area 15.03 squares open
Field shingles 50 bundles open
Ridge and starter 4 more bundles open
Underlayment 2 rolls synthetic open
Sheathing 52 sheets of 4 × 8 open
Attic vents 1,440 sq in net free area open
Gutters 4 downspouts, 140 ft open
Rafters 17 ft 10.7 in at 6:12 open

Working it through by hand: (40 + 2) × (30 + 2) = 1,344 sq ft of footprint; × 1.118 for the 6:12 slope = 1,503 sq ft; ÷ 100 = 15.03 squares; × 1.10 waste × 3 bundles = 49.6, so 50 bundles; 40 ft of ridge ÷ 25 = 1.6, so 2 ridge bundles; 140 ft of perimeter ÷ 120.33 = 1.16, so 2 starter bundles. The order is 54 bundles in all.

Why roof estimating goes wrong

Almost every material shortage on a roof traces back to one of three numbers: the area was measured on the plan instead of the slope, the eaves were left out, or the pitch was guessed. Each one is small on its own. Together they can undershoot a shingle order by 15 to 20%, which is the difference between finishing on Saturday and waiting a week for a second delivery in a different dye lot.

The fix is not a better guess. It is keeping the measurements separate: footprint, overhang, pitch, ridge length and perimeter. Once those are on paper, every quantity on this site is arithmetic, and arithmetic can be checked. That is why each calculator shows its rows instead of only a total, and why the method page lists every rule with the source behind it.

The order to work in

  1. Pitch first. It sets the multiplier that every other area depends on, and it decides which materials are allowed. The pitch calculator gives the ratio, angle and multiplier in one step.
  2. Area second. Footprint plus eaves, times the multiplier, divided by 100. That is the square count.
  3. Then the layers. Shingles, underlayment and sheathing all consume the same squares but at different rates, and each has its own waste rule.
  4. Then the edges. Ridge cap, starter strip, drip edge, gutters and vents are linear or per-piece, so they do not scale with the squares.
  5. Then the structure. Rafter length and ridge height come from the span and the pitch, and they are geometry, not a span table.

What makes this site different

What the numbers cannot tell you

A quantity is not a design. These calculators do not check whether your rafters can carry the load, whether the deck is sound, whether the flashing detail is right, or whether your town requires a permit for the work. They do not know your local rainfall intensity or your snow load. They give you the arithmetic that a roofer, a supplier and a building inspector will all use, so that the conversation starts from the same numbers.

They also assume a simple rectangular roof. An L-shaped house, a cross gable or a dormer is several planes, and each plane needs its own measurement. The calculators handle one rectangle well; a complicated roof is a series of rectangles.

Where the figures come from

Shingle, ridge cap, starter strip and synthetic underlayment coverage come from GAF's published data sheets and installation literature. Slope limits and attic ventilation ratios come from the 2021 International Residential Code, sections R905.2.2 and R806.2. Panel sizes and span ratings come from APA, the engineered wood association. Gutter and downspout capacities come from a published sizing guide that reproduces the industry drainage tables. The pitch multiplier is derived from the Pythagorean theorem and checked against a published multiplier table. All 11 sources are listed with links and reading dates on the method page.

Built for the second opinion

Most people arrive here after a contractor's estimate, a supplier's takeoff or a Saturday morning at a home centre, holding a number they cannot check. The calculators are designed for that moment: put in the measurements you can verify, compare the result with the number on the quote, and if they differ, the rows show exactly where. A difference in squares is a measurement problem. A difference in bundles at the same squares is a waste or rounding difference. A difference in rolls is a product coverage difference. Each one has a different fix.