Roof pitch chart
Every whole pitch from 1:12 to 12:12, with the angle, the slope percentage and the multiplier that turns a horizontal run into roof surface. The arithmetic is shown so you can check any value yourself.
The chart
| Pitch | Angle | Slope | Multiplier |
|---|---|---|---|
| 1:12 | 4.76° | 8.3% | 1.003 |
| 2:12 | 9.46° | 16.7% | 1.014 |
| 3:12 | 14.04° | 25.0% | 1.031 |
| 4:12 | 18.43° | 33.3% | 1.054 |
| 5:12 | 22.62° | 41.7% | 1.083 |
| 6:12 | 26.57° | 50.0% | 1.118 |
| 7:12 | 30.26° | 58.3% | 1.158 |
| 8:12 | 33.69° | 66.7% | 1.202 |
| 9:12 | 36.87° | 75.0% | 1.250 |
| 10:12 | 39.81° | 83.3% | 1.302 |
| 11:12 | 42.51° | 91.7% | 1.357 |
| 12:12 | 45.00° | 100.0% | 1.414 |
Half pitches exist and are common on older roofs: 4.5:12, 5.5:12 and 6.5:12 all appear in framing books. The pitch calculator accepts any rise in quarter-inch steps, so you are not limited to this table.
Where the angle comes from
Pitch is rise over run, so the angle is the arctangent of rise divided by 12. At 6:12 the ratio is 0.5, and arctangent of 0.5 is 26.565°. At 12:12 the ratio is 1, and the angle is 45°. The angle is not linear in the pitch: going from 1:12 to 2:12 adds 4.7°, but going from 11:12 to 12:12 adds only 2.5°.
That curvature is why a roofer's "about 20 degrees" and a 4:12 roof are not the same thing. Four-twelve is 18.43°, and 20° is about 4.37:12. The difference is small on a single rafter but consistent across a whole roof.
Where the percentage comes from
Slope percentage is rise divided by run times 100. A 6:12 roof rises 6 in over 12 in, which is 0.5, or 50%. A 12:12 roof is 100%. Percentage is the unit used by road signs, drainage plans and some European roofing specifications, and it is the one that most often gets confused with degrees because 50% and 45° are close enough to be mistaken for each other at a glance.
The conversion is not interchangeable: 50% slope is 26.57°, not 45°. If a solar or drainage plan gives a percentage, divide by 100 to get the ratio and multiply by 12 to get the pitch.
Deriving the multiplier
The multiplier is the length of the rafter divided by the length of its horizontal run. Take a run of 12 in and a rise of r inches. The rafter is the hypotenuse of a right triangle with legs 12 and r, so its length is √(12² + r²). Divide by 12 to express it per foot of run:
- At 4:12: √(144 + 16) = √160 = 12.649; ÷ 12 = 1.054.
- At 6:12: √(144 + 36) = √180 = 13.416; ÷ 12 = 1.118.
- At 8:12: √(144 + 64) = √208 = 14.422; ÷ 12 = 1.202.
- At 12:12: √(144 + 144) = √288 = 16.971; ÷ 12 = 1.414.
The multiplier is always at least 1 and grows slowly at first, then faster. That is why the jump from 4:12 to 6:12 adds 6% of surface, while the jump from 10:12 to 12:12 adds 8.6% from a smaller base.
Using the multiplier on a real roof
A 40 × 30 ft house with 1 ft eaves has a footprint of 42 × 32 = 1,344 sq ft. At 4:12 the roof surface is 1,344 × 1.054 = 1,417 sq ft, or 14.17 squares. At 8:12 it is 1,344 × 1.202 = 1,615 sq ft, or 16.15 squares. The house did not change; the roof did. That is 2 squares, roughly six bundles, between two pitches people describe as "normal".
The same number drives rafter length: 15 ft of run at 4:12 is 15.81 ft of rafter; at 8:12 it is 18.03 ft. A framer who orders 16 ft lumber for the first roof cannot build the second.
Pitch by roof style and era
Colonial and Cape Cod roofs in the Northeast commonly run 6:12 to 8:12, which sheds snow and fits a steep roofline. Mid-century ranch houses often sit at 3:12 to 5:12, with a low profile and wide eaves. Victorian and Gothic Revival roofs go steeper, 10:12 to 12:12 or more, because the style is vertical. Modern low-slope and flat roofs are under 2:12 and use membrane, not shingles.
Those are patterns, not rules. The pitch on your house is whatever the framer built, and the only way to know is to measure it. Neighbours with the same plan usually match, but an addition often does not.
What pitch decides
- The roof covering. Asphalt shingles need 2:12 or more, with double underlayment below 4:12.
- The material quantity. Everything measured in squares scales with the multiplier.
- The rafter length and the ridge height. Both come straight from the triangle.
- Walkability and fall protection. Above 8:12 most crews use roof jacks; above 12:12 they plan staging.
- Snow shedding and ice dams. Steeper roofs shed more, but the eave detail still decides whether ice backs up.
- Ventilation strategy. A low-slope roof has less attic volume above the ceiling for the same floor area.
Reading pitch off a framing square
A framing square is stamped with pitch tables on the blade and tongue. The row marked "common rafter" gives the length per foot of run for each pitch, which is the multiplier in inches: at 6:12 the table reads 13-7/16, which is 13.4375 in per foot, or 1.120 in decimal. The small difference from 1.118 is rounding in the stamp, not an error.
The same square gives the hip and valley length per foot of run, which is the common-rafter figure multiplied by √2, and the side cuts for each. Those numbers are why a framing square is still in every carpenter's bag.
Checking a chart value
Any value in the table above can be reproduced with a scientific calculator: divide the rise by 12, take the arctangent for the angle, multiply by 100 for the percentage, and take the square root of (1 + ratio²) for the multiplier. If your number disagrees with the chart by more than a rounding step, check whether your calculator is in radians.
Frequently asked
What pitch is 30 degrees?
About 7:12. A 30° roof has a tangent of 0.577, which is 6.93 in of rise per 12 in of run, between 6:12 and 7:12.
What is the most common roof pitch in the US?
Around 4:12 to 6:12 for new residential roofs. Steeper pitches shed snow better; shallower ones use less material and are easier to walk.
Is a 3:12 roof walkable?
It is walkable in dry conditions, but at 14° the shingles give less grip than people expect, and a 3:12 roof is low slope: it needs special underlayment.
How do I convert degrees to pitch?
Take the tangent of the angle and multiply by 12. tan(26.57°) = 0.5, so 26.57° is 6:12. The calculator on the pitch page does it in the other direction.
Where these numbers come from
- Roof Pitch Multiplier: Calculator, Table & Guide — Roof Observations (Jack Gray, RRO), read Nov 20, 2026
- 2021 International Residential Code, R905.2.2 Slope — International Code Council, read Nov 20, 2026
- Minimum Slope for Shingles: What Contractors Need to Know — GAF, read Nov 20, 2026
Figures that come from our own arithmetic rather than a published table are marked house rule on the method page. No price is shown anywhere on this site because no supplier publishes one national figure that would be true for your town and your roof.
Related: pitch calculator · rafter length · roof squares · shingles per square