Shingle calculator
Bundles of field shingles, bundles of ridge cap and bundles of starter strip, counted separately so the order matches what the roof actually needs.
Default scenario: 15 squares of roof, 10% waste, 40 ft of ridge, 100 ft of starter strip. Change a field and recalculate for your roof.
Your result
50 bundles of shingles
plus 2 ridge cap and 1 starter bundles, 53 in total
| Roof area to cover | 16.5 squares | 15 squares + 10% waste |
| Field shingle bundles | 50 | 3 bundles per square, rounded up |
| Ridge cap bundles | 2 | 40 lf ÷ 25 lf per bundle (GAF Seal-A-Ridge) |
| Starter strip bundles | 1 | 100 lf ÷ 120.33 lf per bundle (GAF Pro-Start) |
| Total bundles | 53 | Field + ridge + starter |
- A square is 100 sq ft of finished roof, so the waste allowance is applied to squares rather than to bundles.
- Ridge cap and starter strip are separate products with their own coverage; counting them in the field bundles is the most common ordering mistake.
Before you buy
- Buy every bundle in one order: shingle dye lots vary, and a second order can be visibly different on the same roof.
- Three bundles per square is the standard for 3-tab and most architectural shingles, but a few heavyweight products cover less. Check the bundle label.
The three products in one shingle order
A shingle roof is not one product. It is field shingles, hip and ridge cap, and starter strip, and each one has its own coverage. Most homeowner estimates stop at the field shingles and come up short at the ridge, which is the most visible part of the roof.
| Product | Coverage | What it covers |
|---|---|---|
| Field shingles | 3 bundles per square | The main roof planes |
| Ridge cap | About 25 lf per bundle | Ridges and hips |
| Starter strip | About 120.33 lf per bundle | Eaves and rakes |
The field figure is the one everybody knows: 100 sq ft per square, three bundles per square, about 33.3 sq ft per bundle. It holds for 3-tab and for the great majority of architectural shingles. It does not hold for every product, because a heavier shingle can put less than 33 sq ft in a bundle. The bundle label is the authority, and it is worth reading before you multiply.
Why waste is added to squares, not bundles
Waste is a percentage of the roof area, so it belongs on the squares. Adding 10% to a bundle count that has already been rounded up compounds two roundings and can leave you a bundle or two long. This calculator multiplies the squares by 1.10, then converts to bundles and rounds up once at the end.
Ten percent is a reasonable allowance for a simple gable with two planes and a ridge. A hip roof has four planes, four hips and more cuts, so 15% is the usual figure. A roof with several valleys, a dormer and a chimney can consume 20%. None of those numbers is a manufacturer's published figure, because waste depends on the roof plan; they are planning allowances, and they are labelled as house rules on the method page.
Counting ridge and hip length
Ridge length is the horizontal line at the top of a gable roof: the length of the house, plus any gable extensions. Hips are the four sloping corners of a hip roof; each one runs from a corner of the building up to the ridge, so a simple rectangular hip roof has four hip lines plus the ridge between them.
Measure along the ridge, not along the slope. Ridge cap is installed on the flat top, and its coverage is quoted in linear feet of finished ridge. A 40 ft house with a simple gable has about 40 ft of ridge; the same house with a hip roof has 40 ft of ridge plus four hips of roughly 15 ft each, so 100 ft, or four bundles of cap.
Starter strip, eaves and rakes
Starter strip is a narrower shingle laid upside down along the eaves before the first course. It seals the leading edge against wind uplift and gives the first course a straight line. On a gable roof it runs along both eaves and up both rakes, so the length is the perimeter of the roof, not just the two eaves.
GAF Pro-Start covers about 120.33 linear feet per bundle when the strips are split in half. That is unusually good coverage compared with cutting 3-tab shingles, and it is why a 100 ft perimeter needs one bundle rather than two.
Architectural versus 3-tab
Both are asphalt shingles and both are counted at three bundles per square in the common grades. The differences that matter for an order are weight and profile. Architectural shingles are thicker, so a pallet holds fewer bundles and the load is heavier; a roof that is 50 bundles of 3-tab may be 55 bundles of a laminated product because the bundle covers slightly less.
Three-tab shingles have a flat, repeating tab pattern and a shorter warranty in most lines. Architectural shingles have a dimensional profile and a heavier mat. Neither changes the arithmetic here, but the bundle coverage on the label does.
What this count does not include
- Underlayment. A separate roll count; see the underlayment calculator.
- Ice-dam membrane. Bought by the linear foot at the eaves and in valleys, not by the square.
- Drip edge, valley metal and pipe boots. Sheet metal and flashing, priced by length and by piece.
- Tear-off and disposal. One or two layers of old shingles weigh a lot and need a dumpster.
- Ventilation. Ridge vent and soffit vents are separate; see the ventilation calculator.
Ordering in one go
Shingle dye lots vary. Two bundles made months apart can be visibly different in the same colour name, and the difference shows most on a large, unbroken plane. Order the whole roof at once, including the waste allowance, and keep two or three spare bundles in the garage for future repairs. A spare bundle from the same lot is worth more than the small saving from ordering tight.
Delivery matters too. A shingle order is measured in tons, not bundles, so 50 bundles is a pallet drop rather than a car trip, and the driver will want somewhere flat and close to the roof.
Check the slope before you order
Asphalt shingles are permitted at 2:12 and above. From 2:12 up to 4:12 the code requires double underlayment, and below 2:12 shingles are not an option at all. If your pitch comes out under 4:12, read the underlayment page before you buy anything: the roll count doubles.
A worked example
Fifteen squares, 10% waste, 40 ft of ridge and 100 ft of eaves and rakes. Field shingles: 15 × 1.10 × 3 = 49.5, so 50 bundles. Ridge cap: 40 ÷ 25 = 1.6, so 2 bundles. Starter: 100 ÷ 120.33 = 0.83, so 1 bundle. Total 53 bundles, of which 50 are field shingles.
Frequently asked
How many bundles of shingles do I need for 15 squares?
At 3 bundles per square, 15 squares is 45 bundles. With 10% waste it is 49.5, so 50 bundles, before ridge cap and starter strip.
How many bundles are in a square of shingles?
Three bundles for standard 3-tab and most architectural shingles. A few heavyweight products cover less, so check the bundle label rather than assuming.
How much ridge cap do I need?
About one bundle per 25 linear feet of ridge and hip. GAF Seal-A-Ridge covers 100 ft with four bundles, and each bundle holds 45 caps at a 6 2/3 in exposure.
Do I need starter strip on the rakes too?
Yes on most installations. Starter strip runs along the eaves and up the rake edges, and GAF Pro-Start covers about 120.33 ft per bundle when split.
Can I use the same shingles for ridge cap?
You can cut 3-tab shingles into caps, but a purpose-made hip and ridge product is thicker and seals better. The coverage differs, so count it separately.
Where these numbers come from
- How Many Bundles of Shingles Are in a Square? — GAF, read Nov 20, 2026
- Seal-A-Ridge Ridge Cap Shingles sell sheet (RESHR112) — GAF, read Nov 20, 2026
- Pro-Start Starter Strip Shingles sell sheet (RESGN546) — GAF, read Nov 20, 2026
- 2021 International Residential Code, R905.2.2 Slope — International Code Council, read Nov 20, 2026
Figures that come from our own arithmetic rather than a published table are marked house rule on the method page. No price is shown anywhere on this site because no supplier publishes one national figure that would be true for your town and your roof.
Related: shingles per square · roof squares · underlayment rolls · sheathing panels