RoofCalc.

Roof sheathing calculator

Panels of 4 × 8 or 4 × 10 roof deck for the area you are covering, with waste, and the thickness question that the panel count cannot answer.

Default scenario: 15 squares of deck, 4 × 8 panels, 10% waste. Change a field and recalculate for your roof.

Your result

52 sheets

4 × 8 panels covering 1,650 sq ft with 10% waste

Deck area to cover 15 squares 1,650 sq ft including waste
Panel size 4 × 8 ft 32 sq ft per sheet
Panels needed 52 Rounded up to whole sheets
Edge gap 1/8 in Between panel edges and ends (APA)
Panel thickness 7/16 in or thicker 24/16 span rating for rafters at 24 in on center
  • Roof sheathing is quoted by the sloped area, so the pitch multiplier is already inside the squares figure.
  • A 4 × 8 sheet is 32 sq ft of coverage, but cuts at hips and valleys mean the last sheet of a run is rarely fully used.

Before you buy

  • Confirm the span rating on the panel stamp against your rafter spacing; 3/8 in panels are not a roof deck at 24 in on center.
  • Replace soft or delaminated decking before shingles go on. New shingles do not stiffen an old deck.
  • Follow the nail schedule in IRC Table R602.3(1); nails that miss the rafter are the most common sheathing failure.

What the deck does

Roof sheathing is the structural skin between the rafters and the roofing. It carries snow, wind uplift and the weight of anyone walking the roof, and it ties the rafters together so the roof acts as a diaphragm. It also gives the shingles a flat, nailable surface: a shingle roof over a wavy deck will look wavy for its whole life, no matter how good the shingles are.

That is why the panel count is the easy part. The thickness, span rating, fastening and gaps are the parts that decide whether the deck is code-compliant.

Panel math

A 4 × 8 ft sheet is 32 sq ft. A 4 × 10 sheet is 40 sq ft. Divide the deck area in square feet by the panel area and round up. For 15 squares with 10% waste: 1,500 × 1.10 = 1,650 sq ft, and 1,650 ÷ 32 = 51.6, so 52 sheets.

A roof deck does not need a 10% allowance for the same reason shingles do, but it does need one. Hips, valleys and the rake edge all produce angled cuts, and a sheet that is cut for one corner rarely fits another. Ten percent is a sensible minimum; a cut-up roof with dormers can use 15%.

Thickness and span rating

PanelSpan ratingRafters at 24 in on center
3/8 in24/0Rated at 24 in, but thin and easily damaged underfoot
7/16 in24/16Yes, the common minimum
15/32 in32/16Yes, with margin
19/32 in40/20Yes, heavier deck

The span rating is stamped on the panel and reads as roof span / floor span in inches. A 24/16 panel is rated for rafters at 24 in on center and floor joists at 16 in. Do not translate the number into a thickness by memory: mills produce the same span rating at slightly different thicknesses, and the stamp is what the inspector reads.

Thicker is not automatically better for the roof. A heavier panel adds dead load and cost, and if the rafters are already at their span limit, the extra weight does not buy capacity. Match the panel to the rafter spacing and the code table.

Gaps, orientation and fastening

Panels are laid with the long dimension across the rafters and the ends staggered so four corners do not meet at one point. Leave about 1/8 in between panels at the edges and ends. The gap looks wrong to a first-time installer and is deliberate: wood expands with moisture, and a tight deck buckles at the butt joints, which telegraphs through the shingles as a ridge line.

Nailing follows the schedule in IRC Table R602.3(1): typically 8d common or 6d ring-shank at 6 in on center along supported edges and 12 in in the field, with the nail heads flush. Nails that miss the rafter are worse than no nails, because they hold nothing and puncture the deck from below. On a re-roof, walk the deck and replace any panel that is soft, delaminated or has a nail head standing proud.

OSB, plywood and radiant barrier

Both OSB and plywood are engineered wood panels rated by APA. OSB is made of strands and is more uniform; plywood is made of veneers and tolerates repeated wetting better. For a roof that will be closed in within a week, either is fine. For a deck that may sit open, plywood is more forgiving, and a tarp is better than both.

Radiant-barrier sheathing has a foil face that reflects heat into the attic. It is not a substitute for insulation or ventilation, and it must be installed foil-down with the seams taped if the manufacturer requires it. It also changes the surface the shingles sit on, so follow the shingle manufacturer's approval.

When the deck is the problem

A shingle replacement is the moment to inspect the deck, because it is the only time it is visible. Look for delamination, soft spots around chimneys and valleys, water stains that follow a rafter, and panels that flex underfoot. Replace rather than patch: a new shingle roof over a failing panel inherits the failure, and the warranty will not cover it.

If the deck is sound but the rafters are not, the sheathing calculator is the wrong tool. That is a structural repair, and it starts with the span table and an engineer, not with a panel count.

What this calculator leaves out

A worked example

A 15-square roof with 10% waste needs 1,650 sq ft of deck. In 4 × 8 sheets that is 51.6, so 52 sheets. If you choose 4 × 10 sheets, 1,650 ÷ 40 = 41.25, so 42 sheets. The larger panel means fewer joints and less labour, but it is heavier to handle and harder to fit around hips.

Frequently asked

How many 4 × 8 sheets for a 15 square roof?

52 sheets. Fifteen squares is 1,500 sq ft, plus 10% waste is 1,650 sq ft, divided by 32 sq ft per sheet is 51.6, rounded up.

What thickness of roof sheathing do I need?

For rafters at 24 in on center, 7/16 in OSB with a 24/16 span rating is the common minimum. At 16 in on center, 3/8 in with a 24/0 rating can work, but check the panel stamp and your local code.

Should I leave a gap between panels?

Yes, about 1/8 in at the edges and ends. Panels swell slightly with moisture, and a tight deck can buckle and telegraph through the shingles.

OSB or plywood for a roof deck?

Both are APA-rated and both work. OSB is more uniform and cheaper; plywood holds up better to repeated wetting. Whichever you use, keep it dry before the roof goes on.

Do I need H-clips?

They are required where the panel span rating depends on edge support, typically with thinner panels. The panel stamp and the local code tell you; thick panels at 24 in on center often do not need them.

Where these numbers come from

Figures that come from our own arithmetic rather than a published table are marked house rule on the method page. No price is shown anywhere on this site because no supplier publishes one national figure that would be true for your town and your roof.

Related: roof squares · underlayment · shingles · rafter length